Arduino, running the sketch you wrote
arduino-cli compiles it, an AVR8 core executes it instruction by instruction, and the LCD shows what the ATmega328P actually put on the bus. Uno, Nano, Mega and ATtiny85, no board on your desk.

Hardware is all about iteration. Velxio lets you wire a circuit, program the board and run it in seconds, real firmware on a real solver, right in the browser.
DFRobot · M5Stack links on this page are affiliate links: a purchase through them earns Velxio a small commission at no extra cost to you.
Nothing on this page is a scripted animation: the firmware is compiled and executed, and the circuit around it is solved.
arduino-cli compiles it, an AVR8 core executes it instruction by instruction, and the LCD shows what the ATmega328P actually put on the bus. Uno, Nano, Mega and ATtiny85, no board on your desk.

arduino-cli or ESP-IDF compiles the sketch, then AVR8, RP2040, RISC-V, Xtensa or ARM executes it instruction by instruction. What the OLED draws and what the serial monitor prints is what the chip actually did.

ngspice compiled to WebAssembly runs a full nodal analysis about 60 times a second. GPIO pins drive real nets, ADC inputs read solved node voltages, and probes report RMS, DC and current wherever you drop them.

Adders, comparators, decoders, flip-flops and a 1-bit ALU slice: no microcontroller anywhere, just gates, switches and LEDs solved as a real net. The classroom half of electronics, without the breadboard.

The M5Stack Cardputer with its keyboard, Seeed's round display keeping time, Pimoroni's Badger 2350 driving e-paper, and DFRobot's UNIHIKER M10 in the catalogue alongside them. Their makers sent the hardware so the emulation could be checked against the real thing.




35 boards across 6 CPU architectures — AVR8, ARM Cortex-M, ARM Cortex-A, RISC-V, Xtensa, and Linux. Including partner boards from Pimoroni, M5Stack, Seeed Studio and DFRobot. All running locally, no cloud needed.
One institution contract gives every student in the class a full Pro account. No per-seat checkout, no card details in a classroom.
Private projects, BOM and schematic exports and GitHub Sync, for everyone enrolled.
Billed once to your institution, per semester or per year. Volume pricing on request for large cohorts.
Arduino, ESP32, RP2040, STM32, ATtiny and Raspberry Pi, with SPICE analog solved alongside the firmware. Not a sandboxed mock.
The simulator stays free forever, WiFi with internet included. Paid plans unlock the Linux and STM32 boards, custom WiFi networks and the local network gateway. Maker and Pro add the AI agent; No AI leaves it out.
Discover the simulator + light AI help.
The full workbench, zero AI. You write every line.
For makers shipping real circuits with AI help.
Private projects, GitHub Sync and BOM exports.
Questions, bugs and ideas: the Discord and the issue tracker are open, and so is every line of the simulator.
Robô autônomo com ESP32, sensor ultrassônico, servo SG90 e driver de motores L298P.
An interactive ESP32 circuit simulation you can run free in your browser on Velxio, by marcosfagner.
#include <ESP32Servo.h>
// ESP32 + L298N convencional
// Motor esquerdo: ENA=25, IN1=26, IN2=27
// Motor direito: ENB=14, IN3=32, IN4=33
// HC-SR04: TRIG=5, ECHO=18 (usar divisor resistivo)
// Servo: sinal=19
// Remova os jumpers ENA e ENB do modulo L298N.
#define PIN_ENA 25
#define PIN_IN1 26
#define PIN_IN2 27
#define PIN_ENB 14
#define PIN_IN3 32
#define PIN_IN4 33
#define PIN_TRIG 5
#define PIN_ECHO 18
#define PIN_SERVO 19
const uint32_t FREQUENCIA_PWM = 1000;
const uint8_t RESOLUCAO_PWM = 8;
const int PWM_MAXIMO = 255;
// Altere para true se o respectivo motor girar invertido.
const bool INVERTER_MOTOR_ESQUERDO = false;
const bool INVERTER_MOTOR_DIREITO = false;
const float DISTANCIA_OBSTACULO = 25.0;
const float DISTANCIA_LIBERACAO = 40.0;
const int VELOCIDADE_MAXIMA = 60;
const int VELOCIDADE_MINIMA = 35;
const float DISTANCIA_VELOCIDADE_MAXIMA = 60.0;
const int VELOCIDADE_CURVA = 65;
const int VELOCIDADE_RECUO = 50;
const int ANGULO_CENTRO = 90;
const int ANGULO_ESQUERDA = 170;
const int ANGULO_DIREITA = 10;
const unsigned long TEMPO_RECUO = 350;
const unsigned long TEMPO_CURVA = 450;
const unsigned long TEMPO_GIRO_180 = 900;
const unsigned long TEMPO_SERVO_ESQUERDA = 350;
const unsigned long TEMPO_SERVO_DIREITA = 500;
const unsigned long TEMPO_SERVO_CENTRO = 350;
const unsigned long INTERVALO_LEITURA = 100;
const unsigned long TEMPO_REANALISE = 1000;
const unsigned long TIMEOUT_SENSOR = 30000;
const int MAX_TENTATIVAS_RECUPERACAO = 3;
const int MAX_MANOBRAS_NORMAIS_FALHAS = 3;
Servo meuServo;
float distanciaFrontal = 0;
float distanciaEsquerda = 0;
float distanciaDireita = 0;
bool servoDisponivel = false;
bool motoresDisponiveis = false;
bool proximoGiroEsquerda = true;
int tentativasRecuperacao = 0;
int manobrasNormaisFalhas = 0;
int ultimaVelocidadeExibida = -1;
unsigned long tempoUltimaLeitura = 0;
enum EstadoRobo {
INICIALIZACAO, FRENTE, DETECTOU_OBSTACULO, OLHAR_ESQUERDA,
OLHAR_DIREITA, CENTRALIZAR_SERVO, ANALISAR_DIRECOES, RECUAR,
GIRAR, RECUPERAR_ROTA, VERIFICAR_NOVA_DIRECAO, CAMINHO_BLOQUEADO,
FALHA_SENSOR, IMPASSE, ERRO_HARDWARE
};
EstadoRobo estadoAtual = INICIALIZACAO;
// Compatibilidade com Arduino-ESP32 Core 2.x e 3.x.
#if __has_include(<esp_arduino_version.h>)
#include <esp_arduino_version.h>
#endif
bool configurarPWM() {
#if defined(ESP_ARDUINO_VERSION_MAJOR) && ESP_ARDUINO_VERSION_MAJOR >= 3
bool a = ledcAttach(PIN_ENA, FREQUENCIA_PWM, RESOLUCAO_PWM);
bool b = ledcAttach(PIN_ENB, FREQUENCIA_PWM, RESOLUCAO_PWM);
return a && b;
#else
ledcSetup(0, FREQUENCIA_PWM, RESOLUCAO_PWM);
ledcSetup(1, FREQUENCIA_PWM, RESOLUCAO_PWM);
ledcAttachPin(PIN_ENA, 0);
ledcAttachPin(PIN_ENB, 1);
return true;
#endif
}
void escreverPWM(int pinoEnable, int canal, int valor) {
valor = constrain(valor, 0, PWM_MAXIMO);
#if defined(ESP_ARDUINO_VERSION_MAJOR) && ESP_ARDUINO_VERSION_MAJOR >= 3
ledcWrite(pinoEnable, valor);
#else
ledcWrite(canal, valor);
#endif
}
int calcularVelocidadeAdaptativa(float distan