Arduino, running the sketch you wrote
arduino-cli compiles it, an AVR8 core executes it instruction by instruction, and the LCD shows what the ATmega328P actually put on the bus. Uno, Nano, Mega and ATtiny85, no board on your desk.

Hardware is all about iteration. Velxio lets you wire a circuit, program the board and run it in seconds, real firmware on a real solver, right in the browser.
DFRobot · M5Stack links on this page are affiliate links: a purchase through them earns Velxio a small commission at no extra cost to you.
Nothing on this page is a scripted animation: the firmware is compiled and executed, and the circuit around it is solved.
arduino-cli compiles it, an AVR8 core executes it instruction by instruction, and the LCD shows what the ATmega328P actually put on the bus. Uno, Nano, Mega and ATtiny85, no board on your desk.

arduino-cli or ESP-IDF compiles the sketch, then AVR8, RP2040, RISC-V, Xtensa or ARM executes it instruction by instruction. What the OLED draws and what the serial monitor prints is what the chip actually did.

ngspice compiled to WebAssembly runs a full nodal analysis about 60 times a second. GPIO pins drive real nets, ADC inputs read solved node voltages, and probes report RMS, DC and current wherever you drop them.

Adders, comparators, decoders, flip-flops and a 1-bit ALU slice: no microcontroller anywhere, just gates, switches and LEDs solved as a real net. The classroom half of electronics, without the breadboard.

The M5Stack Cardputer with its keyboard, Seeed's round display keeping time, Pimoroni's Badger 2350 driving e-paper, and DFRobot's UNIHIKER M10 in the catalogue alongside them. Their makers sent the hardware so the emulation could be checked against the real thing.




35 boards across 6 CPU architectures — AVR8, ARM Cortex-M, ARM Cortex-A, RISC-V, Xtensa, and Linux. Including partner boards from Pimoroni, M5Stack, Seeed Studio and DFRobot. All running locally, no cloud needed.
One institution contract gives every student in the class a full Pro account. No per-seat checkout, no card details in a classroom.
Private projects, BOM and schematic exports and GitHub Sync, for everyone enrolled.
Billed once to your institution, per semester or per year. Volume pricing on request for large cohorts.
Arduino, ESP32, RP2040, STM32, ATtiny and Raspberry Pi, with SPICE analog solved alongside the firmware. Not a sandboxed mock.
The simulator stays free forever, WiFi with internet included. Paid plans unlock the Linux and STM32 boards, custom WiFi networks and the local network gateway. Maker and Pro add the AI agent; No AI leaves it out.
Discover the simulator + light AI help.
The full workbench, zero AI. You write every line.
For makers shipping real circuits with AI help.
Private projects, GitHub Sync and BOM exports.
Questions, bugs and ideas: the Discord and the issue tracker are open, and so is every line of the simulator.
Controle de robô ESP32 via ESP-NOW com Joystick analógico
An interactive ESP32 circuit simulation you can run free in your browser on Velxio, by marcosfagner.
#define PIN_VRX 34
#define PIN_VRY 35
#define PIN_SW 27
#define LED_AZUL 25
#define LED_AMARELO 33
// Centro medido nos testes reais
const int CENTRO_X = 1872;
const int CENTRO_Y = 1872;
// Faixa de tolerância para eliminar pequenas oscilações
const int ZONA_MORTA = 120;
bool modoManual = false;
bool estadoBotaoEstavel = HIGH;
bool ultimaLeituraBotao = HIGH;
unsigned long tempoDebounce = 0;
const unsigned long TEMPO_DEBOUNCE = 50;
unsigned long tempoPisca = 0;
bool estadoLedAmarelo = false;
int normalizarEixo(int leitura, int centro) {
if (abs(leitura - centro) <= ZONA_MORTA) {
return 0;
}
int resultado;
if (leitura > centro + ZONA_MORTA) {
resultado = map(
leitura,
centro + ZONA_MORTA,
4095,
0,
100
);
} else {
resultado = map(
leitura,
0,
centro - ZONA_MORTA,
-100,
0
);
}
return constrain(resultado, -100, 100);
}
void verificarBotao() {
bool leituraAtual = digitalRead(PIN_SW);
if (leituraAtual != ultimaLeituraBotao) {
tempoDebounce = millis();
ultimaLeituraBotao = leituraAtual;
}
if (millis() - tempoDebounce >= TEMPO_DEBOUNCE) {
if (leituraAtual != estadoBotaoEstavel) {
estadoBotaoEstavel = leituraAtual;
// O botão é acionado quando vai para LOW
if (estadoBotaoEstavel == LOW) {
modoManual = !modoManual;
Serial.print("MODO ALTERADO: ");
Serial.println(modoManual ? "MANUAL" : "AUTOMATICO");
}
}
}
}
void atualizarLeds() {
// Azul aceso somente no modo manual
digitalWrite(LED_AZUL, modoManual ? HIGH : LOW);
// Amarelo piscando enquanto aguarda conexão com o robô
if (millis() - tempoPisca >= 500) {
tempoPisca = millis();
estadoLedAmarelo = !estadoLedAmarelo;
digitalWrite(LED_AMARELO, estadoLedAmarelo);
}
}
void setup() {
Serial.begin(115200);
pinMode(PIN_SW, INPUT_PULLUP);
pinMode(LED_AZUL, OUTPUT);
pinMode(LED_AMARELO, OUTPUT);
digitalWrite(LED_AZUL, LOW);
digitalWrite(LED_AMARELO, LOW);
delay(500);
Serial.println();
Serial.println("=== TESTE INTEGRADO DO CONTROLE ===");
Serial.println("Comunicacao com o robo: DESATIVADA");
Serial.println("Centro X: 1872 | Centro Y: 1872");
Serial.println("Modo inicial: AUTOMATICO");
}
void loop() {
int leituraX = analogRead(PIN_VRX);
int leituraY = analogRead(PIN_VRY);
int eixoX = normalizarEixo(leituraX, CENTRO_X);
int eixoY = normalizarEixo(leituraY, CENTRO_Y);
verificarBotao();
atualizarLeds();
Serial.print("MODO: ");
Serial.print(modoManual ? "MANUAL" : "AUTOMATICO");
Serial.print(" | X: ");
Serial.print(eixoX);
Serial.print(" | Y: ");
Serial.print(eixoY);
Serial.print(" | ADC X: ");
Serial.print(leituraX);
Serial.print(" | ADC Y: ");
Serial.print(leituraY);
Serial.print(" | BOTAO: ");
Serial.println(digitalRead(PIN_SW) == LOW ? "PRESSIONADO" : "SOLTO");
delay(100);
}